Beiträge von Emanuel

Hello ChristophRe,

thanks for response, i have change my strategy in order to support also the notify on smartphone, now the sensor is activate for ever, and i have added two action on the specific menu when a movement is raised during night and the end of movement, in this way i can have the notify and the bulb that work togheder.

May be that with latest firmware all work as spected also with the previouse settings, but now i have reach a good stability and so i think to leave as is.

Two months and nothing happen.

There is a way in order to program at scheduled time the activation/deactivation of the motion sensor ?

I would turn on a shelly bulb during motion detection of shelly motion only after sunset. There is a way to do this ?

Thanks

Hello,

i have a trouble with this configuration scenes:

1. when button1 is short press (one time) and 1PM is off (one time) then power on 1PM

2. when button1 is short press (one time) and 1PM is on (one time) then power off 1PM

with this configuration i have scene 1 and 2 on a infinite loop.

What is the missing settings in this configuration ?

Thanks

Hello,

i have some problem with my PLUG device, i cannot save the value from APP and using web UI. I would to try to upload a different firmware version, but what is the correct HW version?

I see in the archive firmware list, PLUG and PLUG (v2), the label on my device is Shelly PLUG (S171), but refers to PLUG or PLUG(V2) ?

Thanks

Same problem with 2.0.2 FW , in the settings the motion sensor is enabled, i have setted sunrise and sunset, but the sensor remain active for ever. I have try to reinsert the shedule, reboot, reset but the problem persist.

Where is the settings for notification during vibration?

i haven't found it, during tamper mode i not receive notify or other type of notification thanks

I think that the weekly schedule override the scene, and if i have understood correctly, using weekly schedule you can disable the sensor during day and activate on night.

For the remaining question, well , mee too wait for someone that can help us.

Thank you Eulhofer,

i will try the connection and thanks for the schema.

hello,

is possible to reverse the wires of L and N for power and of for the O in order to drive the neutral instead the line?

In my old house, the wire present in the light switch is the neutral and not the line as usual.

thanks

Hello,

will be possible in the future add the on the scene wizard, the condition based on sunrise/sunset. This capability is usefull for pilot, foe example, a moving sensor onky during night, putting in "and" more conditions.

Thanks

Hello,

is possible known when the battery of button1 is fully charged ?

When connected to power adapter, the ring on the button remain blue and from app interface there isn't battery information, there is only the power connection info.

Thanks

Thanks again for help 66er,

with static configuration the performance are better, around 5 seconds.

Ok, i have try with hostname and the solution proposal by 66er, and work very well.

Thanks for the idea and help

Hello to everybody.

I have configured the url action for short press. When the button1 is not in charge, the time elapsed from button pressed to effective action is about 9-10 seconds. My ip is not static and the url is setted using hostname of device, for example: http://shelly1pm/relay/0?turn=toggle. There are network settings or device settings that can improve the performance ?

Thanks

Thank you 66er,

i use the scenes because there isn't the necessity of set a specific IP, there is a simple wizar on how configure the device based on action. My lan is under dhcp and, i can try, but i'm not sure that the hostname for shelly device work correctly inside my lan.

Do you think that the only simply method for achieve this result is to use the URL settings ?

Thanks

Thank you for the help, i will wait a person that have the button1.

I have try configuring two scenes:

1. When there is a short press on button1 "and" the status of relay is off -> turn on the relay

and another scene

2. When there is a short press on button1 "and" the status of relay is on -> turn off the relay

the relay is a shelly 1PM

but after saved, when i press button1, the scenes go in infinite loop, i have try both settings of realy that are the "status" or the "input", but without lucky.

In any case, thanks again for the help.

Thanks for the reply,

therefore is not possible perform this action with the "scenes" settings ?

I ask for this because i'm not sure that the IP will be the same along the time, and my network is not configured for static IP.

Hello,

i have received today the new Button1 shelly button. I have try to configure it using the scenes settings simulating a toggle switch but i did not succeed.

What i would is to short press the button for turn on the light and short press another time for turn off the same light. Is it possible obtain this behaviour through the mobile app settings?

Thanks for the reply.