Beiträge von dimitrim

Hi,

How can I create an IFTTT applet that allows me to trigger something when the current W consumption is below or higher than a specific threshold with the 1PM?

Thanks, D

Any feedback on this?

Shouldn't I combine the Shelly 1 with a 1PM for this type of setup?

1. Keep using the Shelly 1 to control the ventilator with a volt-free contact to control boost on/off.
2. Next to that put a Shelly 1PM between the regular 220V input of the ventilator and measure the ventilator power consumption.
3. I assume that the ventilator in boost modus will use more electricity so based on the consumption level, I could determine the modus.

Now if my reasoning is correct --- Do you have the option to config the logic to, based on the measurement with the Shelly 1PM, switch the button indicator ON/OFF of the Shelly 1? Can you do this within the Shelly env or should you use IFTTT for that purpose?

Thanks, D

Hi,

I have setup a Shelly 1. With the Shelly app I have configured an Auto Off to 2 secs.

When I press the software button from within the Shelly app, it does what it should do.

However, when I do the same from Google Home I get the impression that the Auto Off is not working. I need to press the button twice to get to the state that I want.

Should I do something else to get this also working with Google home? I would expect all the Shelly 1 settings to be used regardless of the app front-end that you are using.

Thank you

Hi,

I have activated a new Shelly 1. Everything is up and running. I enabled the cloud and I did see the new room and device in the cloud and android app interface. However, I did not see it showing up in my Google Home settings. The other Shelly 1 that I already had in place last week, did show up.

I started the Google Home app. Had a look at the Settings - Works with Google - Shelly and there it only indicated 1 device. I reconnected and at that point all devices showed up. So question - Is this expected behaviour and are you supposed to manually reconnect every time you make some changes?

Thank you

Hi,

I installed another Shelly 1 and got it connected with my heat recovery ventilation system (Vent-Axia Sentinel Kinetic).

The ventilation system also comes with a nr of terminal connections (see attachments). I have connected the Shelly 1 IO to SW4 and can use the Shelly app to switch from a normal (30%) to boost (50%) airflow (and back) modus. Initially I had to push the button twice before it switched back to normal but solved that with setting the Auto Off to 2 secs.

Now it works fine as explained above. One question... Is there a way to get a visual indication that the 50% modus is active? Now it's a just a gray button so if I am not in the proximity of the system, I can only guess how much air it is generating.

Thank you

With my Shelly 1 I am getting a firmware update notification. When I check out the actual update, it suggests that I replace the current 1.8.3 with the same version or sometimes with 1.7.0.
FIRMWARE UPDAT

The current Firmware version of your Shelly is 20200827-065344/v1.8.3@4a8bc427New version 20200601-122823/v1.7.0@d7961837 is available.

The current Firmware version of your Shelly is 20200827-065344/v1.8.3@4a8bc427New version 20200827-065344/v1.8.3@4a8bc427 is available.

Just ignore the msg?

Thanks Stefan. Works like a charm now.

Hi,

I connected a Shelly 1 to a Key Automation system that controls my two garage doors (swing gate principle). Seems to be working but when I close the garage doors, it automatically opens the doors again. I don't use a reed switch for the time being.

L&N are connected to 220V. I&O are connected to the Key Automation printboard ports that are also hooked up to a Niko push button.

https://www.niko.eu/en/products/sw…92-a62c7c239cb4

A push on the Niko button typically opens, stops or closes the doors. This also seems to work like that with the Shelly app but when the doors are closed it automatically opens them again.

Any experience with this type of setup and what settings I should use?

Thanks