Beiträge von downset

Hallo zusammen,

ich hab das Thema jetzt eine weile nicht verfolgt und gerade gesehen das der Thread noch sehr aktiv ist.

daher wollte ich noch einmal ein Update von meiner Seite geben (auch alles Unifi, und im Dezember hier im Thread sehr aktiv gewesen)

In der Zwischenzeit sind noch ein paar mehr Shellys eingezogen ein 1PM mehrere shelly 1 und natürlich weiter die 2.5

ich hatte seit Dezember kein einziges Problem mehr das ein Gerät nicht erreicht werden konnte.

Nach dem downgrade auf 1.7.7 läuft alles einwandfrei.

evtl. sollte hier nochmal genauer geguckt werden was der große Div von der 1.7.7 zu der 1.8.0 und allen weiteren Versionen war.

Viele Grüße

Downset

Zitat

Downgraded to 1.7.7 all devices without any disconnect for more then 48 hours, same WiFi Settings in unifi controller.

so for me only using MQTT without cloud, absolut no problems with this old firmware.

Interestingly this firmware shows no available update.

greets

Downset

Zitat

How is going, are they still online ? Which fw version are you check and what is the AP model and FW.

As i wrote already:

Zitat

in the morning 2 of the 4 devices was disconnected again, after powercycle all came back

in the afternoon one other disconnected and don`t came back with powercyles, i had to reset via pushbutton on the device and reconfigure, so for that device i don`t have any /status results.

one out of 4 survived until i downgraded. (the one with 0 arpchk_resets)

Downgraded again

Zitat

Downgraded to 1.7.7 all devices without any disconnect for more then 48 hours, same WiFi Settings in unifi controller.

so for me only using MQTT without cloud, absolut no problems with this old firmware.

Interestingly this firmware shows no available update.

greets

Downset

UDMB and FlexHD Access Points
Tried all firmwares from unifi including betas now i am on 5.43.21.12519

all shelly FW from 1.8.3 to 1.9.3 rc3 plus the special Firmware from thread are disconnecting

I have not tried the new shelly rc4

1.7.7. still absolute stable

Zitat

As tritter wrote also 1.8.0 is working maybe he is right that the problem starts between 1.8.0 and 1.8.3 but i haven`t tested 1.8.0

greets

Downset

Zitat

Hy, downset

still happy with the 1.7.7 FW?

Cheers

Hi powder8

Yes all fine, not a single disconnect since downgrade

As tritter wrote also 1.8.0 is working maybe he is right that the problem starts between 1.8.0 and 1.8.3 but i haven`t tested 1.8.0

greets Downset

Zitat

Shelly Type: Shelly 2.5 (4 Stück)

Device Mode (wenn Shelly Type Shelly 2.5 ist ) : Roller Shutter

Firmware Version: 1.8.3 /1.9.2 / 1.9.3-RC3 / +Special 2.5 Test Firmware

Router oder AccessPoint: Unify Dream Mashine Base / Unify FlexHD

Static IP oder DHCP: DHCP

WPA Mode: WPA2 only AES/CCMP only

Shelly Type: Shelly RGBW2 (1 Stück)

Gleiches Wlan, Funktioniert ohne Probleme

Alles anzeigen

Downgraded to 1.7.7 all devices without any disconnect for more then 48 hours, same WiFi Settings in unifi controller.

so for me only using MQTT without cloud, absolut no problems with this old firmware.

Interestingly this firmware shows no available update.

greets

Downset

Zitat

Try it

looks good for me until now.

at least 2h all 4 shelly 2.5 online

and no events in unify controller event monitor about permanent roaming or reconnecting of the shelly devices

but too early for final results, will post requested stats after 24h

in the morning 2 of the 4 devices was disconnected again, after powercycle all came back

in the afternoon one other disconnected and don`t came back with powercyles, i had to reset via pushbutton on the device and reconfigure, so for that device i don`t have any /status results.

one out of 4 survived until i downgraded. (the one with 0 arpchk_resets)

Downgraded again

greets

downset

"arpchk_resets":13,"arpchk_results":0,"ram_min_free":28120,"wifi_disconnect_error":0, "wifi_disconnect_timestamp":0

"arpchk_resets":13,"arpchk_results":0,"ram_min_free":31716,"wifi_disconnect_error":0, "wifi_disconnect_timestamp":0,"

"arpchk_resets":0,"arpchk_results":0,"ram_min_free":29480,"wifi_disconnect_error":0, "wifi_disconnect_timestamp":0,"

Zitat

no change for me, all shelly 2.5 are offline during night. doesnt matter if 1.8.3 or 1.9.2 1.8.3 stays about 12h, 1.9.2 for about 2h.

Will now test the special firmware

Try it

looks good for me until now.

at least 2h all 4 shelly 2.5 online

and no events in unify controller event monitor about permanent roaming or reconnecting of the shelly devices

but too early for final results, will post requested stats after 24h

Zitat

Hello For Shelly2.5 we make a special firmware which need to be tested:

LINK: http://repo.shelly.cloud/firmware/dimo/SHSW-25-ACMRAPT.zip

Update command: http://deviceIP/ota?url=LINK

After install you will have new value in http://deviceIP/settings

Looks like that:

"arpchk_resets":0,"arpchk_results":0,"ram_min_free":32356,"wifi_disconnect_error":3, "wifi_disconnect_timestamp":1607607596

To reset the value:

http://deviceIP/reset_debuginfo

Please:

1. Tell us are the device are stable with this firmware and no more disconnects

2. Give us the result from new value after 24 hours.

Alles anzeigen

installed this version on 4 devices.

3 without problems,

one wasn`t reachable after update so i had to reset it physical with the reset Button and reconfigure.

But now it`s working again

did the reset_debuginfo command for all devices, so all counters are actual zero

all 4 devices are now online for 30 minutes witch is not bad compared to 1.9.3 rc3

we will see if they keep to stay connected.

will come back tomorrow after 24h with the stats

edit:

the described values can be found on IP/status not IP/settings

greets downset

Zitat

Hello

To all Unify costumers. There is a new version today which could fix the issue. Please update yours AP and tell is it ok.

https://community.ui.com/releases/UAP-F…OchovEvJ4ONWKGk

smarthome-forum.eu/attachment/13949/

I have this Version already installed as it was released two days ago.

But for me the problem still exists.

1.8.3 keeps longest connected but after a day or so i have to do a Powercycle

1.9.2 and 1.9.3 RC3 both lose connect after a few hours.

At the moment all shelly are on 1.9.3 RC3

2 of my 4 Shelly 2.5 disconnect after 0-2 hours,

the other two sometimes hold connection for a day

greets

downset

SebMai danke für den Hinweis, ist erledigt

Shelly Type: Shelly 2.5 (4 Stück)

Device Mode (wenn Shelly Type Shelly 2.5 ist ) : Roller Shutter

Firmware Version: 1.8.3 /1.9.2 / 1.9.3-RC3

Router oder AccessPoint: Unify Dream Mashine Base / Unify FlexHD

Static IP oder DHCP: DHCP

WPA Mode: WPA2 only AES/CCMP only

Shelly Type: Shelly RGBW2 (1 Stück)

Gleiches Wlan, Funktioniert ohne Probleme

Hallo,

ich habe leider auch weiterhin Verbindungsabbrüche mit der RC3, die nur mit Spannung abschalten und reboot zu beheben sind. Am stabilsten läuft immer noch die shelly Firmware 1.8.X, aber auch da, wenn auch seltener Abbrüche.

Verbindung über Unify Access points (Unify 4x FlexHD und 1x UDMBase)

UDMBase Firmware 1.8.3

FlexHD Firmware sämtliche 5.xx.xx Versionen probiert.

mit sämtlichen einstellungsvarianten hier aus dem Forum Thread zum 1.9 Update ausprobiert.

Result vom /Status:

{"wifi_sta":{"connected":true,"ssid":"XX","ip":"10.XXX.XXX.XXX","rssi":-51},"cloud":{"enabled":false,"connected":false},"mqtt":{"connected":true},"time":"09:58","unixtime":1607248719,"serial":8,"has_update":true,"mac":"68C63AXXXXX","cfg_changed_cnt":2,"actions_stats":{"skipped":0},"rollers":[{"state":"stop","source":"input","power":0.00,"is_valid":true,"safety_switch":false,"overtemperature":false,"stop_reason":"normal","last_direction":"open","current_pos":100,"calibrating":false,"positioning":true}],"meters":[{"power":0.00,"overpower":0.00,"is_valid":true,"timestamp":1607248719,"counters":[0.000, 0.000, 0.000],"total":0},{"power":0.00,"overpower":0.00,"is_valid":true,"timestamp":1607248719,"counters":[0.000, 0.000, 0.000],"total":0}],"inputs":[{"input":0,"event":"","event_cnt":0},{"input":0,"event":"","event_cnt":0}],"temperature":37.47,"overtemperature":false,"tmp":{"tC":37.47,"tF":99.44, "is_valid":true},"temperature_status":"Normal","arpchk_resets":8,"arpchk_results":1,"update":{"status":"pending","has_update":true,"new_version":"20201128-102046/v1.9.2@e83f7025","old_version":"20201202-140039/v1.9.3-rc3@50c6ab57","beta_version":"20201202-140039/v1.9.3-rc3@50c6ab57"},"ram_total":49000,"ram_free":33756,"fs_size":233681,"fs_free":122739,"voltage":229.15,"uptime":250}

Viele Grüße

Downset