Beiträge von slebi

I was able to solve above mentioned issue with setting button type to "Momentary".

i have same issue with bticino matix am5052.

Basically switch has three states:

1. Up
2. Down
3. Stop

If you press UP and after few moments press DOWN, blinds should stop. If you then again press UP/DOWN it should go that way.

Shelly 2.5 is configured as roller shutter, button type is toggle.

I have neutral wire (blue) in the junction box where switch, pictured above, is located.

Brown wires go to I and L, blue goes to N, that's clear. But which one goes to O and SW ? Black to O and gray to SW?

I want to connect Shelly 1 to multiple two way switches but I can't find the correct schema in lexicon for this wiring I have behind the switch. Any suggestions?

Here's the switch (BTicino Classia):

[Blockierte Grafik: https://lh3.googleusercontent.com/92hv6uawifyJUdTY7tO77igel2G4K-JS4caOaVfnlYF6IxrzSwhd7AyE7zaBjPCWW050eZW4w2NP3oA_UmgHZYp1nDMSGHXAuxSoQ7HWKW8MCcR5WdE-e59Ea3oQyc6Zj1xInRw5nU4vMSD7e61AGWzVWjBi3ROqPn22uqL-3ZyUByjecankEnsMFFxTC7Ycn7MoQm16F9zjxV0xy67Jii17dW7sX2vPV1tVFT2LLbtklZ4qSESgzSNzCnDf66BXyL8pA4q0AZBsY_Q6SYelc2YYoqATB6mKayEaeQcG2mJUnjjcVDXlGpTa2epFwtgblORX1-Veqv8EW7yk6GiGUMnngD9smp1Xepq2cI1iy4qw4ALRvTXAqlJttHC800ZXVuz-kA8NF_temPtPxj49QmrsXtqYotedo8ZwFp5iJVsdbYq_YD9ETzSds-xOWxJSMG15BapKXD4McPxs3PwyMwbJa4Ze3rIjgINnbemn7NqW87ZPeqFNMMrpVBK_yI4bZ2nfo9HnP6HwYX-xNx3OeOjbpr6PWoPEUGabjUuPwEUc3S-ZrSzR9X3rDpnfqNPIH3IzWQRxcLnM2wQpsRGj-bNrpPm_yTI-T4P5aNZOJPMaNf5gNu01k_Rk_o2HdpgAZOO2pYd3lfLKvLNNDYOct4hblcyYf2czMsWJAhdzx_AzyvWpqkQCYfBM7cGriOGcrUQ5GrDHQgjAUulJxdNWJbjN=w706-h941-no?authuser=1]

Automatise4life thank you. I was afraid you will say something like that. Because I think I wont be able to fit 4x 2.5 in that box. Or even 1x2.5 and 1xShelly 1 into the box on second picture.

Hi,

I have this switch for venetian blinds and normal switches for lights.

Largest setup looks like this, 2xblinds, and 4x lights (each light has one more switch at the other side of room)

[Blockierte Grafik: https://i.ibb.co/1XFT6dF/IMG-20210201-194148.jpg]

Smallest setup has one shutter switch and one light switch (and only one)

[Blockierte Grafik: https://i.ibb.co/b19DGFS/IMG-20210205-230946.jpg]

Now my question is, can I control second setup with 1xshelly 2.5 and if I can control first setup with 3xshelly 2.5?

Best regards