Beiträge von johnpsom

Zitat

I have that product from the shop mentioned above. It fits perfectly, but is not supported in the firmware, i.e. it does nothing.

OK, Thank you for the input.

Hello,

I have a shelly2.5 to control the open and close of the balcony shader and i can manually stop it to the desired position.

Any ideas on how to schedule and position the opening of the shade at a desired position based on the time of the day?

eg: during night it will be closed fully. During daytime, as the sun is moving, the shader will open in intervals until sunset.

Zitat

Hier kann man die N - Stromzange kaufen.

Shelly 3EM N Stromzange

Thank you...!!!

Have use it? is it working?

Zitat

No problem for me! Thus, you have to open a support ticket to Allterco: https://ticket.shelly.support/open.php

Addendum: Another reason why the current clamps are not offered to buy particularly is: Clamps are matched with the Shelly 3EM in factory to ensure precise measurement.

OK, however i cannot understand why in the manual they have optional the N transformer but no-one can get one!

Zitat

Measuring current, power and energy with a fourth current clamp isn’t supported yet! And if you should get another clamp and fix it at the N port, it wouldn’t work…

I think either you are not correct, or the manual of the product is misleading!!!

https://shelly.cloud/documents/user_guide/shelly_3em_multi_language.pdf

Hello,

does anyone knows where to buy an extra current transformer for the 3M so that to measure the N?

The 3M comes with 3 transformers, but i haven't found anywhere to get another one.

Note: i want the transformer to be the same with the same plug obviously!

Thank you

Zitat

I had similar problems last week with my 3 year old shelly 2.5. First I had no network connection only the connected light switch was working. So I had to restart it by switching the Fuse off and on. It worked for several days again. Then the problems came back even worse. I realized the red led was flickering uncontrolled. Root cause was a faulty elco 100myF /16V. After replacing the shelly is running again.

there is no led on shelly 2.5!!!

Zitat

the connected switch is still working? so you can turn on/off the light with the switch? Then the hardware is not damaged and the reset button (hold for 10 seconds) should definitely work.

As i stated, everything is working. it is only the shelly that cannot be connected, cannot be restarted either via the switch or the reset button.

Hi all,

i cannot connect to shelly 2.5 anymore.

I have tried the reset button as well as the switch method but still no success.

Power is passing through the device. When connected to control a socket or light, the socket or the light are still working.

The issue is that the shelly2.5 device is not connected to anything.

I cannot see the AP after the rest or anything.

Any ideas? How can i check if there is a problem with the device it self?

Correct… i just wanted to add a functionality that the door controller doesn’t have.

Hi,

Sorry if it is not the right place to make such a question.

the pro 2 has two channels 16A each but 25A max.

Is that mean that i can bridge them somehow so that to use it as a single channel 25A?

If not, is it anyone that knows if there are plans to have 25A and 40A Shelly? The things that are most common to control are the kitchen (at 25A at least here in Greece) and the water heater (@20A).

Also if someone has a 32A wall socket already at the garage for electrical vehicles (like i do) it would be great to control it.

Thank you

Since i am an amateur, is it possible to elaborate more on what interposing relay is and where to find one?

Is it also possible to ad what is missing here?

IMG_4276.jpg

Thank you so much

do you think that this below may work?

IMG_4275.jpg

No it is checked. It is AC motor at 220.

By its remote control device. The 7 and 8, is just to connect a local button to operated it. (currently not used).

So i was thinking of using shelly in a way that when the command from the remote is: Open, then current is passing from 6 to the motor to open the door, and thus can trigger the shelly to open the light. and vice versa.

Hi again,

Unfortunately my garage controler, cannot control the light in the garage. Using a Shelly 1 (if needed i can use any other shelly product) how do i do the wiring, and what the settings will be so that, when the garage controller open the door, the Shelly 1 to open the light, and when the controller closes the door, the Shelly to turn off the light.

Bellow is the schematic of the controller.

Garage.jpg

I presume, i have to bridge some how the Open and Close that goes to the Motor, with the Shelly 1, and set it as momentary switch. Now that i am thinking of it, i will need 2 Shelly1 or i will have to use Shelly 2.5 right?
However how tha wiring will be?

Thank you in advance

Great… thank you!

Hi all,

I have put the location to auto. The schedule is set up as in the attached foto.

The question is, if i put +00:30 on the sunset where it switch on, it means that it will switch on the light 30 minutes after the sunset and if -00:30, it will turn on lights 30 minutes before sunset?

Thank youScreenshot 2021-12-27 144807.jpg