Beiträge von xlarge

Hi thgoebel, I need more help.

Still struggling. My Shelly Pro 1 in front of Shelly Pro 1PM handles 3-phase (for water pump), but Pro 1PM (for heat pump) should handle 1-phase and measure consumption.

Right now after installation I find that Pro 1 works OK, but Pro 1PM only shows 1.4w. However, it appears that the Pro 1PM must be on for the heat pump to get power. I believe that only one of the 3 phases is passed through Pro 1PM.

My electrician is also stuck.

Does there have to be an extra contactor or similar that brings together two of the phases from the 3-phase for this to work?

These are my picks for Shelly Pro 1 and Shelly Pro 1PM respectively. The options for Pro 1 seem to work, but according to the shedule, Pro 1PM was supposed to turn off at 03:55 but it didn't.

I struggle at lot with Input/Output settings on both these units.

The Pro 1 is used to schedule a pool pump (some hours day and night) and the Pro 1PM is used to schedule a heat pump (shorter time than the pool pump). The Pro 1 is in front of the Pro 1PM.

What should be the best configuration

Switch or button? and

what relay type? and which choice from

relay power on default?

In addition I like to override the shedule with on/off on the shelly app.

May be extra difficult because the Shelly Pro 1 handle 3-fase to the water pump and the Shelly Pro 1PM handle 1-fase power to the heat pump.

Hi Thomas,

Thank you very much. I will pass it on to the electrician. But I also have a suspicion that the 3-phase is connected incorrectly.

Hi thgoebel,

I think we copied / wired from this picture. But the consumption is not shown (on the Shelly app) and I think the load goes beyond the Shelly Pro 1PM. I had a Deltaco contact after the Shelly and it occasionally showed approx. 180 volts. What is wrong?

If a complete scheme is needed, I hope to get it from the electrician next week.

Hi thgoebel,

Sorry for the delay, but min electrician cannot be reached before Monday. I came back then.

Regards,

xlarge

The heat pump has been running most of this evening, but no change showing in the app. (1.4 w.). Possible 7-8 kwh used.

The 1.4w came during the first minutes after start.

Thank you very much, again.

But the unit (Shelly Pro 1PM) show 1,4 w comsumption which might be what the unit it self use. I need to see the total use in kwh - from my swimming pool heat pump, which is the only connection from the unit.

Something wrong, wire/connection or in the menu?

Hi,

Fixed! I have Shelly app on my huawei mobil - Shelly app, but is there a shelly cloud app for windows? Where to find?

I found the Shelly Pro 1 via ip (on lan), but looking into the settings the ip is "Null". Trying to set fixed ip I got the answer "Not a valid netmask format".

Up and go, but the power comsumption don't work. What can be wrong? Se picture.Screenshot_20220812-151346.pngScreenshot_20220812-152534.png

Screenshot_20220812-151346.png

Hi thgoebel,

Thank you very much for the answer. I really appreciate the recommendation of "Auto On, if device is powered".

But I can't find where it should be done - in the menu.

My electrician and I wonder if we have to use the sw1 when the Shelly pro 1 only will be used to pwer on and off? As in the connection diagram for Shelly Pro 1PM "Device control and monitoring".

And another qestion, can the reset button be used to power on off manually?

Sorry, its urgent as the electrician is still here.

Thank you very much, Robert_M.

My be very simple, but I can't find a diagram for this. I have a Shelly Pro 1 and a temperatur censor Shelly DS18B20, Howto wire/connect them?

Please!

By a mistake I registered my Shelly H&T as "Hidden", but would like to move from there. Howto?

Where in the menu can I set fixed ip? Is it possible to change?

One more detail,

Two shellys: One shelly pro 1 in ap mode. Will the next shelly pro 1pm be able to use that ap? (5 cm from one to another) or should I rather use a lan switch in front of both.

It's a little urgent, I need answer as a electrician come in the middle of the week.

Can I use lan to the first shelly pro 1 and set it in ap mode. Will the next shelly pro 1pm be able to use that ap? (5 cm from one to another).

Hallo,

I am going to use a RJ45 cabel from my router to the Pro 1 and the Pro 1PM. They will be situated in my pools machine room about 20 meters fromt the router in my house.

I wonder if it will work with Lan cabel between the two shellys or I need a split before them?

Another question, one of the shellys must be set i AP mode because I must have wifi there (shelly H&T). Will that confuse the other shelly pro?

If I use Plug S for the plug for the heat pump and want to use shedule for on/off, will the access point still be operational when the unit is off?

My case is a Shelly Pro 1PM and a Shelly Pro 1 inside my pool pump housing and a heat pump outside. The heat pump uses 1.4-2.1 kw. If I use the Plus S for the heat pump, can I also use the access point for contact with the two Shelly Pro? Or would it be better to use a lan cabel?

I also see another use for the Shelly Plug S, namely in my annex where I need a heater in the winter. It will be expensive to leave it on a lot so I want to control it. At the same time, I need to know the temperature inside the annex. Is there another Shelly unit that I would rather use for that?

Hopefully,

xlarge

Hi thgoebel,

What should I do without you and this forum. Thank you very much.

Regards,

xlarge

Sorry, two more questions,

I only need simple control over the 3-fase cirkulation pump. Wifi/lan must be able to shedule and stop/start, but no data of power use or history is needed. Can some other unit than Shelly 3EM be used?

Can lan connection from those units to my broadband connect to Shelly cloud app or must Wifi be used?