Mine received a new v1.11 today
Code
The current Firmware version of your Shelly is 20210726-134925/v1.11.0-pmfix2-g0a2b748Beiträge von L.Sousa
-
-
No news about Shelly Motion on that update?
-
It will say "roller" or "relay" depending on the mode of the unit.
Thank's. But on my mind that has already available!
-
what's the:
13. 'Add mode to the announce topic?'
Regards
-
Bad luck! Mine EM it's 3 years old and no problem! Try the Plug S.
-
Hi, if the produtction isn't higher than the 2500W it should'd be problem but i don't now if Plug S can measure negative values. I have an Shelly EM to measure the solar production and the total comsumption.
-
You might consider using a Shelly EM instead. I have that on my PV inverter.
-
It would even be an excellent improvement to include a connector to connect an external power source to these devices as there is in H&T.
-
Firmware 1.11.2 für Shelly 1PM und PlugS ist jetzt released.
And what's new?
-
MILD LEAK: > 1800 ppm
HEAVY LEAK: > 3000 ppm
But the alarms starts at 1000?
-
I got mine this weekend - Standard PPM-Level is zero.
I tested is in front of our heating wihout igniting the flame - the PPM rose up to 2000 ppm within 5 minutes and the alarm was initiated approximatly for > 1.000 ppm
Thank's. But also should be possible to set the alarm values user want, no?
Regards
-
yes i did that.
I solved it, the powerline wifi was in the wrong place so one sensor got bad signal.
I have a good isolated floor so the signal gets weaker at the sensor underneath the floor.
I got the signal to 'fair' for one sensor and 'poor' for the other one. This seems just enough.
I have a 3 floors house + garage and bfore i also have that signal problem even with powerline, so i have bought an good Mesh system and the bad signal have disappeared....
-
I have bought an external power supply to my garage D&W, works like a charm and don't need a million of batteries...
-
The Static IP it's reserved on the Router server? You must also set the router to don't use the ips you have defined as Static
-
And the V2 has a temperature sensor, and that sensor is not present on the V1.
-
Sorry the toogle mode doesn't work, just blinks....
EDIT: Works just the minimum time its 1 minute betwwwn pulses
-
Sorry i'm really noob!!!
Now i have understaind should be something as
Codehttp://192.168.0.216/relay/0?turn=tooglei think!
-
Ok toogle but how can i set that?
-
Butin the initial configuration i have defined the time to be on as 1 minute and the action appears as http://192.168.0.216/relay/0?turn=on so no timer, that shows the auto config isn't correct....
Question 2 : it's possible to first shelly motion activation turns light on and second activation turns off?
I go to the garage and passing the sensor the light turn on, i can remain the time i want on the garage and when i goes off garage when i pass to the sensor lights turns off...
-
Patience or even using the search yourself are unfortunately not your strengths, right?
What I do here, I do in my leisure, just to mention it again. Just like my teammates, I don't make any money with it.
You could also have followed my signature link to the http commands.
But here you go:
You have to set the right ip of light switching shelly !
Should i replace the code on the action the http://192.168.0.216/relay/0?turn=on
to that code: http://192.168.0.216/relay/0?turn=on&timer=120
to shutt off on two minutes?
Its strange because by defaut as i can see the timer isn't showered on the original configuration as you can see