Hi all,
Did not find a way to control the thermostat in the wall display (MQTT or others) from 'outside'.
I have a wall display but did not install it yet because I want to be able to switch on and off the heating from my domotics system.
So it does not start heating when we are not home, and to integrate it in the 'all off' when we leave.
Did anyone achieve this in some way?
Hi all,
Anyone had the experience of false alarms?
It worked fine for a while, but then started to trigger every night (sound & app but not MQTT).
Installed in a colder environment, I want it there because I charge my e-bike there. Is that the cause? Because it worked will in middle of the winter, few weeks ago it started to misbehave.
If have other installed in my house, they don't behave like this.
That part is in the scene to switch the light off; I changed the timer to 8 minutes in the meantime.
If 60 Seconds works better than its 100% this issue here:
I still am not convinced about that. Before, even without any shower / bath / blow-drying for more than 24 hours (this is the 2nd bathroom), it almost always happened. And until now (statistics are not 100% final because of short test period) never had it happen, even after a shower. So I do not need any modifications for now, completely happy with how it works at the moment.
It seems the blind time of 60 seconds works better. I don't really understand why (30 seconds should be enough to ignore the closing of the door?) but most important is that it works better now.
The cloud scene looks fine to me, make sure you have not set up 2 or more scenes by mistake, also no blu alexa scenes, and that there is no blue script running on that shelly.
--->A quick fix, or at least worth a try, would be to increase the bind time to 60.
Have you tried this?
Only 1 scene to switch on, 1 scene to switch off, no other scenes. No Alexa or scripts active. I just activated the blind time of 60 seconds,device had to be replaced because there are issues with firmware update (got bricked afte a few tries, new one does not want to update either BTW). I will monitor and keep informed.
I suppose it is a cloud scene, see attached. Usually I do stuff like that through MQTT, but BLU does not support that I am afraid. I don't think the bathroom aspect is the issue. Even when humidity is perfectly standard and the bathroom is like any other room, it does this. Even when only having brushed my teeth, or random during the day when I enter to take something for 5 seconds.
Hi all,
I am controlling my bothroom light with this LBU motion sensor. To switch on automatically and to switch of after 5 minutes (we tend to forget sometimes to switch it off). Outside the door, we have a switch connected to the PM2 controlling the light, so after going outside and closing the door, we switch of the light using this switch. But almost always, the light switches on again a few seconds later. If we switch it off again, it stays off. I configured a blind time of 30 seconds in the BLU motion, but without any result. How could we avoid this? Why does the light switch on again?
All,
I wanted to replace a hardware thermostat with the wall display in my attick bathroom, since I have quite some Shelly devices there.
When adding those devices in the wall display, I notice that most of them show as offline (which they are not). However, most devices do not have cloud enabled because I use MQTT functionality, and these devices cannot combine both.
I have 1 devcie with cloud enabled, and that one shows correctly.
I hope cloud does not have to be enabled for a device to be useable on the wall display, that would be a complete showstopper. The temperature measurement and plug I want to use as thermostat sensor and output, would also be not useabl then.
Anyone have similar experience or solution?
Exactly the same request from my side. Change the temperature setpoint and/or enable the thermostat is very much on my whishlist too.
But I do not think it is possible for the moment.
Hi all,
I have a smoke sensor in my porch (charging my e-bike there) but for 2 days in a row, the alarm is triggered when the sun is on the roof and it gets hot in there.
According to what i find, it should only be trigered by smoke, which is definitely not present there.
Anyone have a similar experience?
Yes, but it does not seem to describe what I am looking for. I always find it easier to search through a pdf instead of the small print, in that case it is easier to miss what you are looking for.
I want to reset the device, made a typo in the password and now I am locked out...
I received my device today.
But I cannot find the manual. How to include, how to wake it up to access the web interface etc.
Dear all,
The temperature in my Motion 2 shows NULL in the app, 999 through MQQT and temperature measurement 'disabled' in the web page.
Never changed it, it worked for a while. i have no knowledge of a way to disable or enable the temperature measurement?
Anyone had something similar. And better still, know a solution?
Thanks,
